Triumph Oil Pumps Stocked By
BCS
70-9421 Stock Triumph Unit Oil Pump
70-3072 Stock Triumph Pre-Unit Oil Pump
Latest two valve type, fitted as stock on Triumph 500, 650 and 750 twins.
(unit twin shown, pre-unit is similar but not interchangeable)
71-7317 Four Valve Triumph Unit Oil Pump
Stock Triumph Unit Oil Pump, four valve type, fitted as stock on unit
construction Triumph late 750 twins. Retro fits to all earlier 650 and 750 unit
twins. Comes with instructions. Some very minor modifications needed.
71-7317 Installation Instructions
70-9421/B Morgo Plunger Triumph Unit Oil Pump
70-3072/A Morgo Plunger Triumph Pre-Unit Oil Pump
The Morgo Unit high performance plunger pump is made to very fine limits from
the best materials to give long and trouble free service and a 20% increase in
performance over the standard oil pump. No modifications are needed just take
off the old pump and fit the new. The unit pumps can be fitted to all twin
cylinder unit construction motors.
The Morgo Pre-Unit high performance plunger pump is made to very fine limits
from the best materials to give long and trouble free service and a 20% increase
in performance over the standard oil pump. No modifications are needed just take
off the old pump and fit the new. The pre-unit pumps can be fitted to all twin
cylinder pre-unit motors.
70-9421/A Morgo Rotary Triumph Unit Oil Pump Kit
70-3072/B Morgo Rotary Triumph Pre-Unit Oil Pump Kit
Why should I buy a new Morgo
Super Rotary oil pump? To put the matter into simple terms it is all about
efficiency, reliability, balance, performance, heat and peace of mind.
EFFICIENCY AND RELIABILITY
The new Morgo Super Rotary pump
is capable of delivering approximately 3 to 4 pints of oil a minute when the oil
is hot. A rotary pump of the new type will still pump oil adequately when the
oil is in a very contaminated condition, and the pump is very worn. Normally the
contamination in the oil would hold open the ball valves in the plunger type
pumps, and stop the pump working at pressure, scavenge, or both. Resulting in
either no oil pressure or the crank case full of oil. No number of extra ball
valves can eliminate this possibility.
BALANCE
Although our Morgo plunger pumps have stood the test of time and will always
give good value for money, the reciprocating action of the plunger pump promotes
an out of balance situation, resulting in pulsation of the oil flow, noise and
vibration. The new rotary pump gives the opposite and has a more shock absorbing
effect, because the load on the cam drive gear train is more constant, and not
on and off load all the time the engine is running.
HEAT - THE ENGINES ENEMY
It has been reported back to us by customers that they have noticed a significant decrease in engine temperature. This can only be attributed to the greater oil flow, establishing that the oil is doing a better job of both lubricating and cooling the engine. Having oil coolers fitted is of great benefit, but is a waste of time if the oil flow is so slow as to allow the oil to dwell too long in the engine without passing through the oil cooler. The oil cooler can only be fully effective if the oil circulation can transfer the heat to the oil cooler radiator effectively ie. if the oil is spending too much time in the engine it is helping to store the heat instead of dispersing it.
QUALITY
The plunger type Morgo pumps are manufactured to a very high standard. But because of the very small amount of effective stroke out of the total plunger travel, all the vacuum and pressure has to be created within no more than 4.5mm from the bottom of the plunger bores, therefore the smallest amount of bore, or plunger wear has a very detrimental effect on the pumps performance. In the case of a rotary pump, as wear occurs over a much greater mileage, the oil flow and pressure capability remains surprisingly constant throughout the long life of the rotary type pump. If anything, in our experience the performance seems to improve.
When you order tell us the type of threads in your engine UNF or CYCLE, your engine may not be the original one for your machine.
We have no objection whatsoever
to you comparing the cost of our range of Morgo equipment, as long as you also
compare the quality, all Morgo equipment is made in England. Ask for Morgo by
name, and then you have our full support behind you.
WHAT'S IN THE KIT
1 Rotary pump.
1 Drive nut.
1 Drive coupling.
1 Gasket.
4 Shims.
2 Bolts.
1 Allen key.
Morgo Triumph Rotary
Unit Oil Pump Kit Instructions
Morgo Triumph
Rotary Pre-Unit Oil Pump Kit Instructions
Morgo Triumph Rotary Oil
Pump FAQ